| Notes: 4: Requires some trimming of the air dam., 4: Requires some trimming of the air dam.: 4: 84-89 Acura Integras utilize 2 different brackets. The distinction is usually between 2dr and 4dr. However very rarely, the frames have been interchanged, requiring the opposite bracket design. To verify which bracket is necessary, look at the bolts that hold the E-A unit (Energy Absorbtion Unit) to the frame tower on the drivers side. If the E-A unit is bolted on with 3 bolts@ 1,7,& 9 o'clock positions, then the 1510-3 designed for the 2dr is necessary. If it is bolted with 2 bolts, one at 3 o'clock & 9 o'clock positions, then the 1510-1 designed for the 4dr is to be used. If it is bolted with 2 bolts, one @ 1 o'clock & one @ 7 o'clock, neither bracket will work., 4: Requires some trimming of the air dam.: 4: 84-89 Acura Integras utilize 2 different brackets. The distinction is usually between 2dr and 4dr. However very rarely, the frames have been interchanged, requiring the opposite bracket design. To verify which bracket is necessary, look at the bolts that hold the E-A unit (Energy Absorbtion Unit) to the frame tower on the drivers side. If the E-A unit is bolted on with 3 bolts@ 1,7,& 9 o'clock positions, then the 1510-3 designed for the 2dr is necessary. If it is bolted with 2 bolts, one at 3 o'clock & 9 o'clock positions, then the 1510-1 designed for the 4dr is to be used. If it is bolted with 2 bolts, one @ 1 o'clock & one @ 7 o'clock, neither bracket will work.: 4: Baseplate is concealed through the bumper opening.Notes: 4: Requires some trimming of the air dam.: 4: 84-89 Acura Integras utilize 2 different brackets. The distinction is usually between 2dr and 4dr. However very rarely, the frames have been interchanged, requiring the opposite bracket design. To verify which bracket is necessary, look at the bolts that hold the E-A unit (Energy Absorbtion Unit) to the frame tower on the drivers side. If the E-A unit is bolted on with 3 bolts@ 1,7,& 9 o'clock positions, then the 1510-3 designed for the 2dr is necessary. If it is bolted with 2 bolts, one at 3 o'clock & 9 o'clock positions, then the 1510-1 designed for the 4dr is to be used. If it is bolted with 2 bolts, one @ 1 o'clock & one @ 7 o'clock, neither bracket will work.: 4: Baseplate is concealed through the bumper opening.: 9: Tow hooks must be removed and remain off the vehicle after installation., 4: Requires some trimming of the air dam.: 4: 84-89 Acura Integras utilize 2 different brackets. The distinction is usually between 2dr and 4dr. However very rarely, the frames have been interchanged, requiring the opposite bracket design. To verify which bracket is necessary, look at the bolts that hold the E-A unit (Energy Absorbtion Unit) to the frame tower on the drivers side. If the E-A unit is bolted on with 3 bolts@ 1,7,& 9 o'clock positions, then the 1510-3 designed for the 2dr is necessary. If it is bolted with 2 bolts, one at 3 o'clock & 9 o'clock positions, then the 1510-1 designed for the 4dr is to be used. If it is bolted with 2 bolts, one @ 1 o'clock & one @ 7 o'clock, neither bracket will work.: 4: Baseplate is concealed through the bumper opening.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper., 4: Requires some trimming of the air dam.: 4: 84-89 Acura Integras utilize 2 different brackets. The distinction is usually between 2dr and 4dr. However very rarely, the frames have been interchanged, requiring the opposite bracket design. To verify which bracket is necessary, look at the bolts that hold the E-A unit (Energy Absorbtion Unit) to the frame tower on the drivers side. If the E-A unit is bolted on with 3 bolts@ 1,7,& 9 o'clock positions, then the 1510-3 designed for the 2dr is necessary. If it is bolted with 2 bolts, one at 3 o'clock & 9 o'clock positions, then the 1510-1 designed for the 4dr is to be used. If it is bolted with 2 bolts, one @ 1 o'clock & one @ 7 o'clock, neither bracket will work.: 4: Baseplate is concealed through the bumper opening.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper.: 9: Baseplate is adaptable to BlueOx tow bars with a 3-prong clevis.Notes: 4: Requires some trimming of the air dam.: 4: 84-89 Acura Integras utilize 2 different brackets. The distinction is usually between 2dr and 4dr. However very rarely, the frames have been interchanged, requiring the opposite bracket design. To verify which bracket is necessary, look at the bolts that hold the E-A unit (Energy Absorbtion Unit) to the frame tower on the drivers side. If the E-A unit is bolted on with 3 bolts@ 1,7,& 9 o'clock positions, then the 1510-3 designed for the 2dr is necessary. If it is bolted with 2 bolts, one at 3 o'clock & 9 o'clock positions, then the 1510-1 designed for the 4dr is to be used. If it is bolted with 2 bolts, one @ 1 o'clock & one @ 7 o'clock, neither bracket will work.: 4: Baseplate is concealed through the bumper opening.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper.: 9: Baseplate is adaptable to BlueOx tow bars with a 3-prong clevis.: 10: The vehicle must have factory tow hooks to mount the bracket to. |